I'd like to learn how to do it by hand and by just plugging it in an app. Can anyone steer me in the right direction?

- Thread starter IPAAAA
- Start date

I'd like to learn how to do it by hand and by just plugging it in an app. Can anyone steer me in the right direction?

Check out BobbyM's All Grain Primer, he does a good job of explaining it all, good luck.

- Thread Starter
- #3

Checking it out now...thanks.Check out BobbyM's All Grain Primer, he does a good job of explaining it all, good luck.

- Thread Starter
- #4

So I checked it out and this is what I got. The efficiency just seems way to high to me. Am I doing something wrong? Just to clarify this calculation is for the mash efficiency and not the brewing efficiency right?

Pale Malt 2 Row - US - 2.0 srm (36ppg) x 7lb + cara-pils/dextrine 2.0 srm (32ppg) x .75lb + caramel/cyrstal malt 15 srm (35ppg) x .50lb + vienna malt 3.5 srm (35ppg) x .50lb = 252+24+17.5+17.5= 311 gravity points available

Gravity points available / Collected Volume in Gallons = Maximum Original Gravity

311/7gal = 44.4 or an maximum SG of 1.044.

Measured Specific Gravity in Points / Maximum Specific Gravity in Points = Efficiency

42/44 = .95 or 95% efficiency

Pale Malt 2 Row - US - 2.0 srm (36ppg) x 7lb + cara-pils/dextrine 2.0 srm (32ppg) x .75lb + caramel/cyrstal malt 15 srm (35ppg) x .50lb + vienna malt 3.5 srm (35ppg) x .50lb = 252+24+17.5+17.5= 311 gravity points available

Gravity points available / Collected Volume in Gallons = Maximum Original Gravity

311/7gal = 44.4 or an maximum SG of 1.044.

Measured Specific Gravity in Points / Maximum Specific Gravity in Points = Efficiency

42/44 = .95 or 95% efficiency

The formula looks right, but my question is, that 42, is that pre boil or post boil? If it's pre-boil, then you did it right. Maybe your 7 gallons of collected wort is wrong? 6.75 gallons makes it 46 points. 6.5 gallons makes it 48 points. 42/48 makes it 87.5% if that makes you feel better

Pale Malt 2 Row - US - 2.0 srm (36ppg) x 7lb + cara-pils/dextrine 2.0 srm (32ppg) x .75lb + caramel/cyrstal malt 15 srm (35ppg) x .50lb + vienna malt 3.5 srm (35ppg) x .50lb = 252+24+17.5+17.5= 311 gravity points available

Gravity points available / Collected Volume in Gallons = Maximum Original Gravity

311/7gal = 44.4 or an maximum SG of 1.044.

Measured Specific Gravity in Points / Maximum Specific Gravity in Points = Efficiency

42/44 = .95 or 95% efficiency

Assuming your 42 was pre boil and your volume is accurate, you just happened to mash the hell out of those grains.

- Thread Starter
- #7

That a online publication?

Based off my notes I have 1.042 preboil and 1.046 post boil. That sound right?The formula looks right, but my question is, that 42, is that pre boil or post boil? If it's pre-boil, then you did it right. Maybe your 7 gallons of collected wort is wrong? 6.75 gallons makes it 46 points. 6.5 gallons makes it 48 points. 42/48 makes it 87.5% if that makes you feel better

Assuming your 42 was pre boil and your volume is accurate, you just happened to mash the hell out of those grains.

I am pretty sure I hit 7 gallons right on the money and I calculated that amount prior to mashing and sparging. Now you got me second guessing my notes. :cross:

Based off the information above...what is the forumula to figure out my brewhouse efficiency?

Only 4 points after an hour long boil doesn't seem right to me. When I used to brew inside, on my stove, it was a pretty solid 10 points my pre to post boil difference. Now that I've done my last 6 or 7 batches outside, on a stronger burner, my difference is more like 12-14 points (stronger boil off, stronger concentration, higher gravity)That a online publication?

Based off my notes I have 1.042 preboil and 1.046 post boil. That sound right?

Which are you more sure of, the 42 or the 46? If the 42 is right, then you got 95% like you said. If the 46 post boil is right, I'll

Uh, what? You calculated that you collected 7 gallons PRIOR to mashing and sparging? The sparge waterI am pretty sure I hit 7 gallons right on the money and I calculated that amount prior to mashing and sparging. Now you got me second guessing my notes. :cross:

So, let's say you mashed with 5 gallons of water, got 3 gallons out. Maybe you need 7 gallons of total volume, so you do your two 2 gallon sparges (or one four gallon sparge, whatever), now you've got your 7 gallons. Is that what you mean your total volume came from? Or are you talking about the total volume you used?

I'm not really keen on the "brewhouse efficiency". To me, all that is important is what I'm getting out of my mashtun and that it is consistent. I used to worry "zomfg I didn't get 99.99% eff" or whatever. I've got my system dialed in and I get a solid 78-82% efficiency. I think most people are satisfied with 70% or better, but to me its just important to get roughly the same number each time. (Yes, Saccromeyecyessesese, I no you no sparge and are happy with the lower efficiency, because it saves you 20-40 minutes on your brew day)Based off the information above...what is the forumula to figure out my brewhouse efficiency?

- Thread Starter
- #10

I am more sure of the 42 but now that I think about it the wort might not have been fully cooled. I did let it sit for a while though in the hydrometer which was placed in a bowl of water. Guess it isn't a huge deal but now I know for my future brews.Only 4 points after an hour long boil doesn't seem right to me. When I used to brew inside, on my stove, it was a pretty solid 10 points my pre to post boil difference. Now that I've done my last 6 or 7 batches outside, on a stronger burner, my difference is more like 12-14 points (stronger boil off, stronger concentration, higher gravity)

Which are you more sure of, the 42 or the 46? If the 42 is right, then you got 95% like you said. If the 46 post boil is right, I'llguessthat your pre-boil was 34-36 which would make your efficiency 77-82%. Either way, sounds like it turned out pretty good.

Ment to say I calculated 7 gallons of total volume to hit my 5 gallon post boil. That worked out dead on the money.Uh, what? You calculated that you collected 7 gallons PRIOR to mashing and sparging? The sparge waterinis usually pretty darn close to the sparge water you getout. Your strike water for the mash will be significantly less out than what you put in. Off hand, if you mash with 5 gallons, you're probably only going to get 2-3 gallons of wort out (don't hold me to those numbers, but it's something like that).

So, let's say you mashed with 5 gallons of water, got 3 gallons out. Maybe you need 7 gallons of total volume, so you do your two 2 gallon sparges (or one four gallon sparge, whatever), now you've got your 7 gallons. Is that what you mean your total volume came from? Or are you talking about the total volume you used?

Ya, I agree I just wanted to know how this all works. I usually don't get technical with things like this but it had me curious. Knowing the procedure and how to figure it out will help me visualize things better. I will keep searching since BobbyM's All Grain Primer didn't go over the brewhouse efficiency.I'm not really keen on the "brewhouse efficiency". To me, all that is important is what I'm getting out of my mashtun and that it is consistent. I used to worry "zomfg I didn't get 99.99% eff" or whatever. I've got my system dialed in and I get a solid 78-82% efficiency. I think most people are satisfied with 70% or better, but to me its just important to get roughly the same number each time. (Yes, Saccromeyecyessesese, I no you no sparge and are happy with the lower efficiency, because it saves you 20-40 minutes on your brew day)

Thanks again for the help.

- Replies
- 3

- Views
- 2K